Tile and Grout
How to Clean and Seal Grout So It Stays Clean
Grout turns gray because it soaks up dirty mop water. Deep clean it, rinse, let it dry, then seal it. Steps, supplies and at-home care from Sandy, OR.
Quick answer: Grout turns gray because it is porous and absorbs the dirty water left behind every time a floor is mopped. To bring it back, deep clean the grout lines with a nylon brush, rinse them with clean water, let them dry completely, and apply a clear penetrating sealer. Afterward, clean with a pH-neutral cleaner, use bleach and stiff brushes sparingly, and dry the floor after you mop.
Most of the gray grout we see in kitchens, entries and bathrooms around Sandy, OR started out white or light beige, and the color usually comes from soil that can be cleaned out. Getting it back depends on order. Clean deep, rinse everything out, and seal, so the grout stops drinking up dirt.
Affiliate disclosure: Some links in this article go to products on Amazon. As an Amazon Associate we earn from qualifying purchases. The price you pay stays the same.

Why grout turns gray
Standard grout is mostly cement and sand. The Tile Council of North America (TCNA) describes it as porous, with a large surface area that absorbs stains. When you mop, dirty water runs off the glazed tile and settles in the joints, which sit a little lower than the tile face. The grout soaks up that water along with grease, soap film and whatever came in on shoes. A mop can't pull it back out, and during a wet East County winter, mud at the entry speeds things up.
TCNA also notes that cement dissolves in acid, so vinegar eats into grout, while oil soaps and wax cleaners leave a film that collects more dirt. A penetrating sealer makes the grout repel water, so spills bead on top long enough to be wiped away.
How to clean and seal grout, step by step
Plan on two days. Wear nitrile gloves, open a window or run the bath fan, and test each product on a hidden spot first.
- Sweep or vacuum. Loose grit turns to mud in the joints once it gets wet.
- Apply cleaner to a 3-by-3-foot section. Use a pH-neutral tile cleaner, or an oxygen cleaner for heavier soil on ceramic or porcelain. Mix it per the label and give it the listed dwell time.
- Scrub the joints with a nylon grout brush. Use short strokes and steady pressure. Wire brushes and scouring pads scratch tile and wear grout down.
- Rinse with clean water and remove it. Use a fresh bucket, then pick up the dirty water with a wet/dry shop vacuum or microfiber cloths. TCNA calls applying cleaner and vacuuming up the dirty water the best way to clean grout, because it lifts dirt off the joint. Residue attracts soil and can block sealer, so rinse twice if the water looks cloudy.
- Let the grout dry completely. Wet grout looks darker. Wait until every line is back to its dry color, usually overnight.
- Apply a clear penetrating sealer to the grout lines. Run an applicator bottle along each joint. The technical data sheet for Aqua Mix Sealer's Choice Gold says to let it penetrate up to 5 minutes, then wipe the surface completely dry.
- Test and recoat if needed. Aqua Mix calls for 30 minutes between coats and a water-drop test after 2 hours. If a drop soaks in and darkens the joint, add a coat.
- Let it cure. For that sealer, Aqua Mix lists light foot traffic after 2 hours, no water for 12 hours, and a full cure at 24 hours. Follow the label on whichever sealer you use.


What you'll need
- pH-neutral tile cleaner: Black Diamond Stoneworks Marble & Tile Floor Cleaner. Stone-safe and sealer-safe, so it doubles as your weekly cleaner.
- Oxygen cleaner (optional): OxiClean Versatile Stain Remover Powder for heavier soil on ceramic or porcelain. Skip it on natural stone.
- Nylon grout brush: OXO Good Grips Grout Brush. The narrow head fits grout lines.
- Clear penetrating sealer: Aqua Mix Sealer's Choice Gold, 1 quart. Water-based, no sheen, rated for grout and natural stone.
- Sealer applicator: Marshalltown 12 oz grout sealer roller bottle for floors, or the QEP 4 oz brush bottle for shower walls.
- Microfiber cloths: Amazon Basics microfiber cloths, 24 pack, for rinsing, wiping and drying.
- Nitrile gloves: GLOVEWORKS HD black nitrile gloves, box of 100, which Aqua Mix's data sheet calls for. They run small, so consider one size up.
- A bucket, plus a wet/dry shop vacuum if you have one.
Add all 7 items to your Amazon cart
The cart button adds the roller bottle and size Medium gloves. Swap either in your cart if needed. Amazon may ask you to sign in first.
Mistakes that wear grout down
- Cleaning with vinegar or other acids. They dissolve grout and etch marble, limestone and travertine.
- Using bleach every week. Ryan Marino of TCNA told Architectural Digest that highly alkaline cleaners "can strip away sealant from the grout over time." Save bleach for mildew spots, and never mix it with ammonia or acids.
- Scrubbing hard with stiff brushes every week. Keep the nylon brush for deep cleans.
- Sealing grout that is damp or dirty. Sealer locks in whatever is already in the joint.
- Letting sealer dry on the tile. Aqua Mix warns that a white film can form.
How to keep sealed grout clean
Sweep before you mop, and mop with a diluted pH-neutral cleaner. Change the water once it turns gray, or use a microfiber flat mop, so you aren't spreading dirt back into the joints. Then dry the floor with a towel or dry pad so water doesn't sit in the grout lines. In showers, squeegee the walls and run the fan. Keep a mat at each door through the rainy months.
Repeat the water-drop test once or twice a year. When drops soak in, reseal. Most homes need it every year or two, and busy kitchens and entries sooner.

When to call a pro
Call a professional if the grout is cracked, crumbling or missing, if it stays gray after a full deep clean, if the tile is natural stone such as slate, travertine or marble, or if shower mildew returns within weeks, which can point to water getting behind the tile.
Sandy Carpet Cleaners is one call away
We deep clean tile and grout on floors, shower walls and natural stone, then apply a clear penetrating sealer, for homes in Sandy, OR and nearby towns from Gresham to Estacada. See our tile and grout cleaning service for what a visit includes, or call (971) 446-7578 for a free written quote. Every job is backed by our satisfaction guarantee.
Grout cleaning FAQ
How often should grout be sealed?
Most homes need it every year or two, and high-traffic kitchens and entries more often. Reseal when a drop of water soaks in and darkens the grout.
Can I use bleach to clean grout?
Occasionally, for mildew spots, followed by a good rinse. Regular use of strong alkaline cleaners like bleach can strip sealer from grout over time.
Does a clear sealer change the color of grout?
A penetrating sealer such as Sealer's Choice Gold is designed to leave a natural, no-sheen look. Test a hidden spot first, since some grout and stone can look slightly darker. Color sealing tints the grout, and we don't offer it.
Can I clean natural stone tile the same way?
Use only a stone-safe pH-neutral cleaner, a nylon brush and clean water on marble, travertine, limestone or slate. Vinegar, bleach and oxygen cleaners can etch or dull the surface.
More articles
- How to Clean Mattress Stains and Odors at HomeBlot mattress stains with little water, dry the bed fully, and see when a stain or odor means you should call a pro.
- Best Everyday Vacuums for Homes with PetsA CRI Seal of Approval shortlist for pet hair on carpet, plus how often to vacuum and when a vacuum is not enough.
- How to Get Pet Vomit Smell Out of CarpetScrape and blot pet vomit, then treat the odor with a pet enzyme cleaner. Why vomit differs from urine, and when the smell means you should call a pro.
Free quote
Let's get your floors fresh
Tell us what needs cleaning in Sandy, Oregon, or nearby. We'll get back to you during phone hours, Mon–Fri 8 AM–6 PM, and we can book after-hours and weekend appointments. Questions first? Read the FAQ.
